Red Seal certified & insured Open 8AM - 8PM, Monday to Sunday $100 diagnostic, applied to your repair 4.8/5 from 1,100+ Google reviews
Close-up of a white front-load washer's cycle dial and buttons, including the Spin button and the Rinse and Spin and Spin Only settings

Washing machine not spinning? Causes and how to fix it


A washing machine not spinning is most often reacting to the load, the settings or water it can't drain, not to a broken part. Check that the spin speed isn't set to No Spin, spread out a heavy or lopsided load, and make sure the washer has drained. If the drum still won't turn, worn motor brushes, a slipped belt, a faulty door lock or a control board is the likely cause, and that's a job for our washing machine repair technicians.

Unplug the washer before you open the pump filter or move it. Turn off the taps behind it, and put towels down first.

Key Takeaways

  • Samsung says an unbalanced load is the most likely reason a washer stops spinning. One heavy item washed alone, like a rug or a pair of runners, can do it.
  • A washer won't spin while water is still in the drum, so a clogged pump filter or kinked drain hose stops the spin cycle too.
  • Too much detergent, or the wrong kind, makes suds that slow or stop the spin. Metro Vancouver's water is soft, so the usual dose on the bottle can be too much.
  • If the washer fills and drains but the drum won't turn, suspect the motor brushes, belt, door lock or control board.
  • Loud banging in spin, then no spin, often means a broken spider arm. That usually means a new washer.

Why is my washing machine not spinning?

Before the drum spins fast, the door or lid has to lock, the water has to drain, and the load has to sit evenly. If any of these fails, the washer slows the spin or skips it. That's why most no-spin problems clear up without parts.

The spin checks in a washing machineA vertical flow chart of five numbered boxes joined by downward arrows: door or lid locks; water drains out; load sits evenly; motor turns the drum; spin cycle. A highlighted note says a failed check slows or skips the spin, and that the first three are often fixable at home. The source line credits Vancouver Appliance Service Pros.What has to happen before a washer spinsEach check must pass, in this order1. Door or lid locksdoor lock, latch or lid switch2. Water drains outpump filter, drain pump and drain hose3. Load sits evenlythe washer senses an unbalanced or heavy load4. Motor turns the drumbrushes, belt, motor sensor and control board5. Spin cyclethe drum speeds up and throws the water outIf any check fails, the washer slows the spinor skips it. Steps 1 to 3 are often fixable at home.Diagram: Vancouver Appliance Service Pros
A washer checks the door, the drain and the load before it spins. The motor parts come last.

Match what you see, then go to the step.

What you seeLikely causeStart with
Clothes soaking wet, drum tried to spin then stoppedUnbalanced or overloaded drumStep 2
Washer rocks or walks during spinNot level, or shipping bolts still inStep 3
Water left in the drumClogged pump filter or drain hoseStep 5
Lots of suds at the end of the cycleToo much detergentStep 4
Fills and drains, but the drum never turnsMotor brushes, belt or motorCall for service
Hums or clicks, door won't lockDoor lock or lid switchStep 6, then service
Bangs loudly in spin, then stopsBroken spider arm or worn bearingsCall for service

How to fix a washing machine that won't spin

Work through these in order. The first four take a few minutes and need few or no tools.

  1. Check the cycle and spin speed. Whirlpool notes that "If Low Spin or No Spin was selected, the washer might not remove enough water from the load." Delicate and hand-wash cycles spin slowly on purpose. Pick a Normal cycle with a high spin speed and try again.
  2. Rebalance the load. Whirlpool says "If the load is too heavy or unevenly distributed, the washer may become unstable and stop spinning to avoid damage." Spread wet items around the drum. Single heavy items cause the most trouble. Samsung warns that "Heavy items like trainers, when washed alone, can also cause imbalance." LG adds pillows and rugs. If the drum is packed full, take a few items out.
  3. Level the washer. Whirlpool says "The washer must be level." All four feet should touch the floor. LG says to adjust the front levelling foot on the low side. On a brand-new front-loader, check that the shipping bolts were taken out. We've removed them from 7 newly installed washers that shook and walked across the floor.
  4. Cut the detergent. Whirlpool says "The excess suds can cause the washer to run at a reduced spin speed, resulting in very wet loads or error codes." It also says that with very soft water, "you may need to use less detergent". That applies here. Metro Vancouver's 2024 water quality report puts treated-water hardness at about 22 mg/L or lower at all three sources, which is soft water. GE calls this a suds lock, and says "Using high efficiency (HE) detergent decreases the possibility of suds lock happening." Run a rinse with no detergent to clear them.
  5. Drain it and clean the pump filter. Samsung explains that "If the drum has stopped draining, the machine will not spin properly." First check that the drain hose behind the washer isn't kinked or crushed. On a front-loader, the pump filter sits behind a small door at the bottom front. Put down towels and a shallow tray, then open it slowly. LG warns "The water may be hot, so exercise caution." After a hot cycle, let it cool first. On our calls, the pump filter and hoses are where we find socks, coins, cards from a wallet and even sand.
  6. Close the door or lid firmly and reset. GE says none of its top-load washers will spin with the lid up, and on its front-loaders "The Washer will not spin if the dispenser drawer is not fully closed." Then power-cycle the washer. GE's reset is to unplug the washer for 2 minutes. Plug it back in and run a drain-and-spin cycle.

If water won't leave the drum at all, our guide to a washing machine not draining goes deeper on the pump, hoses and standpipe.

When the drum won't turn at all

If the washer fills, washes and drains, but the drum never spins, the drive system has failed. These are the parts we find on those calls.

Worn motor carbon brushes

Some front-loaders, Blomberg among them, use a motor with two carbon brushes that wear down over time. When they're too short, the motor can't turn the drum. On our calls, when a Blomberg front-loader fills and drains but the drum won't turn, it's usually the brushes. 28 of our 31 recent brush replacements were Blombergs, and new brushes got the drum spinning again.

Blomberg front-load washer with the back panel off, showing the large drum pulley and drive belt, next to a gloved hand holding a bag of new green motor carbon brushes
Photo from one of our service calls in Burnaby: a Blomberg front-loader that filled and drained but wouldn't turn the drum. The motor carbon brushes were worn too far to make good contact. We fitted the new brushes shown, and the washer tested fine.

Drive belt off or broken

On belt-drive washers, a belt that has slipped off or snapped lets the motor run without turning the drum. Sometimes the pulley bolt has worked loose. Direct-drive washers have no belt.

Broken grey drive belt hanging loose behind an Electrolux washer in a laundry closet, in front of the water supply taps
Photo from one of our service calls in Vancouver: the snapped drive belt from an Electrolux front-loader booked for not spinning. The motor was running, but with the belt broken it couldn't drive the drum. A new belt fixed it.

Door lock or lid switch

A washer won't spin unless it knows the door or lid is shut. A failed lock, latch or lid switch stops the spin even when the door looks shut. GE says "the lid must lock for the washer to spin." We replace door locks, latches and handles often, and Blomberg door handles come up again and again on our calls.

Control board or motor sensor

The control board tells the motor when to spin. On several of our board calls, the fix was a loose connector, not a new board. If the washer won't start any cycle at all, check the washing machine fuse. A failed board can stop the spin cycle and often shows an error code. On Samsung models, motor faults usually show one of these codes: 3C, 3E, 3E1, 3E2, 3E3 or 3E4. On the LG washers we've seen with a motor error, the fix was the motor's speed (Hall) sensor or the stator.

Broken spider arm or drum support

Loud banging during spin, then a drum that won't spin, often means the spider arm or crosspiece behind the drum has broken. Our technicians link these failures to overloading. It generally means a new washer, because the repair can cost more than the machine is worth. If yours is rattling rather than banging, see our guide to a rattling washing machine.

Samsung and GE washers that won't spin

Samsung washing machine not spinning

Samsung washers show UB or UE when they sense an unbalanced load. Samsung's fix: "If the laundry is unbalanced and the UB information displayed, redistribute the load." If water stays in the drum, Samsung says you'll normally see a 5C code, which points to the drain. If the drum won't turn at all, Samsung says "it's possible that it needs service due to a motor issue."

GE washing machine not spinning

On a GE top-loader, make sure the lid is down and locks. GE notes that "pauses of up to three minutes may occur between cycles", so wait before you decide it's stuck. On GE front-loaders, close the dispenser drawer fully, and know that "If the load size is too small, the Washer may not spin." GE Hydrowave top-loaders have their own motor reset: unplug for 1 minute, plug back in, then lift and lower the lid 6 times within 12 seconds.

What a no-spin repair costs in Vancouver

We charge a $100 flat diagnostic, which comes off the labour if you go ahead. Most repairs fall between $225 and $300 in labour, with the diagnostic included, and parts are quoted before we order them. Brushes, belts, lid switches and control boards are quoted for your exact model. Our washing machine service page puts most washer repairs at $275 to $500 all-in, including the diagnostic, labour and part. A stacked washer in a condo closet can add labour, because the dryer has to come off first. Our Vancouver appliance repair prices page has the full list.

No-spin questions we get asked

Is there a reset button on washers?

Most washers don't have one. To reset a washing machine to spin, cut the power instead. GE says to unplug the washer for 2 minutes. LG says to unplug it and, "While the washer remains without power, press and hold the Start/Pause button for 5 seconds." Samsung UK says to switch off at the mains and wait 30 seconds. A reset clears a stuck control, not a worn part.

How do I get my washing machine to just spin?

Choose the drain-and-spin cycle. Whirlpool says "To remove extra water in the load, select the 'Drain & Spin' cycle." LG calls it Rinse and Spin. To test the washer itself, LG suggests you "perform a RINSE AND SPIN cycle with nothing in the drum". If the empty drum spins, the load was the problem. If not, a part has failed.

Is it worth fixing a washing machine that won't spin?

Usually, if the washer is under 7 years old and the fault is brushes, a belt, a lid switch or a door lock. A broken spider arm or worn bearings on a washer over 10 years old usually isn't worth it. Our guide to washer repair cost and when to replace walks through the numbers.

Tips to keep your washer spinning

  • Don't overload the drum. Leave room to move, and wash heavy items with a few smaller ones.
  • Use HE detergent and measure it. In soft water, start below the line on the bottle.
  • Empty pockets. Coins, cards and socks end up in the pump.
  • Clean the pump filter and door boot regularly. Our guide on how to clean a washing machine covers both.

Still not spinning? Vancouver Appliance Service Pros fixes washers across Vancouver and the Lower Mainland, 8 AM to 8 PM, seven days a week. Call 604-265-3852 or book a visit online, and we'll tell you whether it's a quick part or time for a new washer.

More about our technicians, or see the areas we serve.

Open 8AM - 8PM, Monday to Sunday · 2 appointments available today & tomorrow

Need Professional Appliance Repair Help In Vancouver?


or book an appointment online today

Call Now Book Online